请教一个在linux2.4下驱动S3C44B0上的网络和液晶显示屏驱动问题
我把我编好的内核移植到 S3C44B0 上时，上电启动后如下：
Starting kernel ...
Linux version 2.4.24-uc0 (root@linux-nugw) (gcc version 2.95.3 20010315 (release
)(ColdFire patches - 20010318 from http://fiddes.net/coldfire/)(uClinux XIP and
shared lib patches from http://www.snapgear.com/)) #9 2007骞?01鏈?20鏃?鏄熸湡
鍏?14:41:08 CST
Processor: Samsung S3C44B0X revision 0
Architecture: S3C44B0X
On node 0 totalpages: 2048
zone(0): 0 pages.
zone(1): 2048
zone(2): 0 pages.
Kernel command line: root=/dev/rom0 init=/linuxrc
Console: colour dummy device 80x30
Calibrating delay loop... 23.85 BogoMIPS
Memory: 8MB = 8MB total
Memory: 4956KB available (2825K code, 211K data, 60K init)
Dentry cache hash table entries: 1024 (order: 1, 8192 bytes)
Inode cache hash table entries: 512 (order: 0, 4096 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 2048 (order: 1, 819
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
ttyS%d0 at I/O 0x1d00000 (irq = 3) is a S3C44B0
ttyS%d1 at I/O 0x1d04000 (irq = 2) is a S3C44B0
LCD buffer : 0c340000
ne.c:v1.10 9/23/94 Donald Becker (becker@scyld.com)
Last modified Nov 1, 2000 by Paul Gortmaker
NE*000 ethercard probe at 0x6060000:NE2000 driver m
time.net
00 49 34 00 00 00
eth0: NE2000 found at 0x6060000, using IRQ 24
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: C1152F0-C2D96EF [VIRTUAL C1152F0-C2D96EF] (RO)
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 512)
NET4: Unix domain sockets 1.0/SMP for Linux NET4
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
VFS: Mounted root (romfs filesystem) readonly.
Freeing init memory: 60K
Shell invoked to run file: /etc/rc
Command: hostname Samsung
Command: /bin/expand /etc/ramfs.img /dev/ram0
Command: /bin/expand /etc/ramfs2048.img /dev/ram1
Command: mount -t proc proc /proc
Command: mount -t ext2 /dev/ram0 /var
Command: mkdir /var/config
Command: mkdir /var/tmp
Command: mkdir /var/log
Command: mkdir /var/run
Command: mkdir /var/lock
Command: mkdir /var/empty
Command: ifconfig lo 127.0.0.1
Command: route add -net 127.0.0.0 netmask 255.255.255.0 lo
Command: ifconfig eth0 192.168.0.28 netmask 255.255.255.0 up
Command: cat /etc/motd
Welcome to
____ _ _
/ __| ||_|
_ _| | | | _ ____ _ _ _ _
| | | | | | || | _ \| | | |\ \/ /
| |_| | |__| || | | | | |_| |/ \
| ___\____|_||_|_| |_|\____|\_/\_/
| |
|_|
For further information check:
http://www.uclinux.org/
Command:
Execution Finished, Exiting
Sash command shell (version 1.1
可是在 ping 或者是在 ifconfig eth0 192.168.0.28 的时候没不能通过啊 ！
我的液晶显示好象也有了，可是就是在虚拟目录下看不到，这是怎么一回事情！希望高手指点！谢谢！QQ：99592177！
说明：在ping 127.0.0.1的时候能 通过的！
[解决办法]
那可是加载有问题吧
你的驱动是动态加载的??
module
[解决办法]
其实一提到软硬的问题,就让人头大,主要原因
软件可能受到硬件的影响,或者相反等等.
你这种问题,如果内核编译没有问题,或许可能是硬件.但不排除其它因素.
如果不行,你可以试着,再编译几次内核,选上一定要选上的.试几下.
有可能你的加载模块有些没有弄上.
想的.
[解决办法]
先看看eth0 的状态 cat /proc/net/dev
lspci
cat /proc/interrupts
确定驱动和内核都没有问题，仔细检查一下的内核参数。
ping不通不能代表你的网卡不能工作，如果ping是时断时好的，考虑网络线路本身问题、网卡器件稳定问题、内核调度是否繁忙，网络是否繁忙等原因
